What is 192.168.1.1 (192.168.0.1)
192.168.1.1 (192.168.0.1) is a commonly used default IP address for entering the router configuration page. It is also called “Settings page”, “Configuration page”, “Router Setup page”, etc. First of all you should see the login page when you are to enter login and password and then you should be taken to settings web interface. Users often ask why cannot I access router settings via 192.168.1.1 or even a login page. You may face such errors as: “ERR_CONNECTION_TIMED_OUT” or “Page unavailable 404”. Below we will mention all possible reasons why your router configuration or login page might be unavailable and give some pieces of advice on how to gain access to your router settings 192.168.1.1.
How to Access Router Settings Page at 192.168.1.1 or 192.168.0.1
Here what you need to know first. To be able to access config page you need either to connect via Wi-Fi or via the Ethernet cable to LAN port.
Do not connect the ethernet cable to ports labelled “WAN” or “Internet”!
Find the IP of your router
Wrong IP address
Ip you input wrong IP address you will surely get the error:
This site can't be reached. 192.168.1.1 took too long to respond. ERR_CONNECTION_TIMED_OUT
How to find the correct router’s IP?
So, first ensure you are trying to acces your router using the correct IP address. The IP address may be different from default value such as 192.168.1.1. Even if 192.168.1.1 is printed on the back of the device it might have been changed in the past by anyone who accessed the device. To find the IP address of your router:
- Launch the command prompt.
- Hit “Enter”.
Default gateway = your router’s IP address. In our example the gateway IP address is not 192.168.1.1 but 192.168.43.1 cause we are connected to a mobile hotspot on Android and the smartphone acts as a router:
Username and Password to Access Router Settings
Check if you are typing correct login and password. However, if you type wrong credentials you would be told “wrong username or password” or will see the login request but you won’t see “error 404”:
Check the sticker on your router’s back panel to find the factory default IP, username and password:
Most Common Default Credentials (IP, Username and Password)
If you have lost a manual to your router, there is no sticker on its back with default credentials or you cannot find the gateway IP address for some reason, you may try the following credentials.
Most common default router IP-addresses:
Most common credentials:
- admin/(blank password)
The most spread router IP addresses are 192.168.1.1 and 192.168.0.1. The most spread credentials are: “admin/admin” or “admin” with an empty password.
HTTP is used instead of HTTPS
In modern routers you might need to type
https://192.168.1.1 instead of
http://192.168.1.1. Try this.
Reboot Your Router
Very often a glitch on your router can prevent you from logging in to its settings page. The webinterface can become unavailable after a long period of work without reboot. So, power cycle your router, wait for two minutes and try to access the login page once again:
Solve Problems With Your Browser
First of all try another browser to access router’s configuration page at 192.168.1.1 or another IP address. Check browser settings and make sure:
- proxy is disabled for local addresses:
- there is no policy on Google Chrome (how to remove policies from Chrome);
- there are no extensions installed that are able to change IP addresses and routes.
At last reset browser’s settings:
Solve The Problem With Network To Access Router Settings
Common network problem can be the reason why you cannot access router config page. So, please check the following things:
- Ensure your network connection is activated;
- Ensure IP/DNS are set to be obtained automatically: If a static IP is manually assigned to your network card it may be from another subnet or conflict with your router’s LAN IP address:
- Clear Hosts.
- Delete static routes.
- Try disabling your antivirus.
If you are an unexperienced user in networking, we recommend that you use NetAdapter Repair All In One utility to automatically solve such problems:
Replace the Ethernet Cable
Damaged ethernet patch cord can be the reason why you cannot access your router login page on http://192.168.1.1.
It is obvious that if you can open all websites on the Internet but only the router web interface this means your cable is likely to be okay.
Reset Router Settings
If you have tried everything but nothing helps to access the router settings on the web interface, you have to try resetting your device to the factory defaults. In most cases you should press and hold the hidden RESET button for 15-30 seconds while the router is powered on:
Why Am I Redirected to Google After Typing “192.168.1.1”?
Ensure you are not entering a space before the IP address. You’d better enter the whole URL http://192.168.1.1 into the address bar:
Commas instead of dots?
If you enter 192,168,1,1 with commas instead of dots…
…you would be taken to your default search engine:
Summary: How to Finally Gain Access to Router Settings at http://192.168.1.1
Okay, let’s say you don’t remember your credentials or even you want to set up the unfamiliar device. Well, the shortest way to open http://192.168.1.1 and access the configuration page of any router is:
- Factory reset the router by pressing and holding the RESET button on the device for 15-30 seconds while it is powered on.
- Connect a LAN port of your router to the network card of your desktop PC or laptop with an ethernet cable:
- Make sure your network card is configured to obtain an IP address and DNS server address automatically.
- Find the gateway IP address using ipconfig /all command in the command line:
- Type http://your-gateway-address in the address bar of your browser and hit Enter.
- Type default username and password that is specified on the sticker located on the router’s back panel:
Tell us in the comments which tip helped you access router settings page.